VISIÓN GENERAL
The Club Dash Logger (CDL3) comes standard as a combined backlit display and powerful control device in one lightweight unit. With the addition of the Data Logging upgrade it becomes a fully programmable data logger with 8 MB memory.
It offers the same construction and advanced technology as the top of the line ADL3, with a package of features tailored to entry level motorsport requirements.
The screen layout is fully configurable to display a multitude of data channels, warning alarms, lap times, fuel calculations, minimum corner speeds, maximum straight speeds and more.
The CDL3 performs calculations, acquiring data from other devices such as an ECU.
FUNCIONALIDES
- All-in-one display, logger and controller (logging and I/O optional)
- Suitable for bikes, cars, marine and industrial applications
- Compact, durable and reliable unit
- Supports Wideband Lambda from MoTeC PLMs or LTCs
- Easily integrates with MoTeC CAN-based expanders, GPS, shift lights and ECUs
- Alarm acknowledge, mode, page and scroll line buttons
- 2 stage brightness control input
- SLM / SLM-C for shift and warning light
COMPATIBILIDAD
MoTeC ECU Models
- M84, M400, M600, M800, M800, M1 Series (package dependant)
- Discontinued: M4, M48, M8
An additional cable/adaptor may be required in conjunction with the RS232 adaptor for some ECUs
MoTeC Accessories
- MDD, E888, SLM, SLM-C, PLM, LTC, BR2, PDMs, GPS, VCS
Other
- Many non-MoTeC devices
KITS Y ACCESORIOS
Kits
- 18023 – CDL3 Track Display Kit
- 18024 – CDL3 Track Logging Kit
Kit Components
- 18122 – SLM-C Club Shift Light Module
- 62203 – Loom, CDL3 terminated
- 61221 – Loom, Two button
- 41304 – GPS L10, 10hz GPS
Accessories
- 61222 – Terminated Curly cord
- 61199 – CDL3 to RS232 ECU (an additional cable/adapter may also be required for some ECUs)
- 61198 – CDL3 to MoTeC CAN ECU
- 61197 – CDL3 to OBD-II
- 61196 – CDL3 Input Loom
ESPECIFICACIONES
Display
- 70 segment bar graph
- 13 digit alphanumeric text bar
- 48 user-defined, scrollable message lines with programmable overrides
- 3 programmable ‘pages’ for Practice, Warm-Up and Race
- Adjustable backlight
Logging – optional
- 8 MB logging memory
- Logging rates up to 500 samples per second
- Fast Ethernet download
Inputs – optional
- 4 x Analogue voltage high resolution inputs
- 2 x Analogue temperature inputs
- 2 x Digital inputs
- 3 x Speed inputs
- Compatible with E888 expander (8 thermocouples only)
Outputs – optional
- 4 x PWM, switched or digital outputs
Internal Sensors
- 3-axis accelerometer, detection range: +/- 5G
- Dash temperature sensor
- Sensor supply voltage
- Battery voltage
Communications
- 2 x configurable CAN or RS232 bus with individually programmable CAN bus speeds
- 1 dedicated RS232
Physical
- Dimensions 180 x 91 x 18 mm excluding connector
- Weight 385 g
- 1 x 34 pin AMP connector
SOFTWARE
Windows-based software designed for setup and management of the display* and data logging* system, that provides:
- Configuration of the inputs, ouputs, LEDs*, display*, data logging* and calculations
- Offline generation of a configuration file that can then be sent to the device.
- Channel monitoring
- Firmware updating and extensive help screens
* Where applicable based on the device.
ETHERNET WIRING
| Ethernet Connector | MoTeC Loom Colour | CDL3 | ||
|---|---|---|---|---|
| Pin | Function | Pin | Function | |
| 1 | ethernet TX + | orange/white | 11 | ethernet RX + |
| 2 | ethernet TX – | orange | 10 | ethernet RX – |
| 3 | ethernet RX + | green/white | 2 | ethernet TX + |
| 6 | ethernet RX – | green | 1 | ethernet TX – |
The wiring specified is the preferred cross-over configuration. However, the wiring can also be configured as straight-through. Cat 5 Ethernet cable must be used.
Pin Numbering
CABLEADO DE ETHERNET
When using an M4, M48 or M8 ECU, the CDL3 should be connected via RS232. For some ECUs, a PCI cable may also be required.
The Display Logger should be connected via the CAN bus when using a ‘hundred series’ ECU(M400/M600/M800/M880) or M84, and any number of other CAN devices. See the following example.
