D153
VISION GENERAL
The D153 display is part of MoTeC’s D1 Series. This compact, configurable and high brightness colour display is readable in direct sunlight; it is used with M1 ECUs and Dash/Enclosed loggers.
Selectable fixed display layouts offer multiple style options or use Display Creator software for full screen customisation.
It is designed primarily for mounting on steering wheels, with inputs provided to suit steering wheel mounted switches that allow transmission of switch state on CAN.
CARACTERISTICAS
- Colour LCD display
- Compact size to allow mounting on steering wheels
- High brightness for sunlight readability
- 8 Analogue inputs
- 6 Switch inputs
- Receives data from M1 ECUs and Dash/Enclosed Loggers via CAN
- Sends input data to other devices via CAN
ESPECIFICACIONES
Analog inputs
- Amount: 8 (can be used for switches or potentiometers)
- Measurement range: 0V to 4V
- Maximum operating voltage = 7.0V *
- Maximum protected voltage = 32V
- Input equivalent: 10kΩ to 4.0V
* Above this voltage other inputs may be affected.
Switch inputs
- Amount: 6
- Threshold High max = 3.5V
- Threshold Low min = 0.8V
- Maximum operating voltage = 32V
- Input equivalent: 10kΩ to 4.0V
Power supply
- Operating voltage = 6.5V to 32V
- Operating current = 380mA (typical) at 14V, full brightness
- Reverse battery protected
Communications
- CAN 1 Mbit/sec
Display
- Type: TFT LCD, anti-reflective
- Resolution: 320 x 240, anti-aliased graphics
- Brightness: controlled via CAN message, 100 steps
- Layouts: selectable fixed layouts
- Display Creator software provides the tools for full screen customisation
Operating temperature
- Internal: -20°C to 70°C (above 60°C maximum backlight brightness progressively reduced)
- Typical maximum ambient temperature in free air: 50°C
Physical
- Weight: 200gms (excluding wiring)
- Anodised aluminium housing
COMPATIBILIDAD
- MoTeC ECUs: All models that support CAN communication
- MoTeC Displays/Loggers: All
- BACK TO TOP
SOFTWARE
- MoTeC ECUs: All models that support CAN communication
- MoTeC Displays/Loggers: All
SOFTWARE
- Microsoft Windows based software
- Display Creator allows for full customisation of the screen layout
- Dash Manager used for setup and management of the display when combined with a C series Display/Display Logger
DIMENSIONES Y MONTAJE
PINOUT
No terminating connectors, two unterminated flying leads (cables A and B).
Cable A
| Wire Colour | Name | Function | Internal Pin |
|---|---|---|---|
| Black | Bat Neg | Battery Negative | A 1 |
| Red | Bat Pos | Battery Positive | A 2 |
| Green | * CAN LO | CAN Bus Low | A 3 |
| White | * CAN HI | CAN Bus High | A 4 |
| Brown | AN1 | Analog Input 1 | A 7 |
| Orange | AN2 | Analog Input 2 | A 8 |
| Yellow | AN3 | Analog Input 3 | A 9 |
| Blue | AN4 | Analog Input 4 | A 10 |
| Violet | AN5 | Analog Input 5 | A 11 |
| Grey | 0V | Sensor 0 Volts | A 18 |
Cable B
| Wire Colour | Name | Function | Internal Pin |
|---|---|---|---|
| Green | SW1 | Switch Input 1 | B 5 |
| Blue | SW2 | Switch Input 2 | B 6 |
| Violet | SW3 | Switch Input 3 | B 7 |
| Grey | SW4 | Switch Input 4 | B 8 |
| Orange | SW5 | Switch Input 5 | B 9 |
| Yellow | SW6 | Switch Input 6 | B 10 |
| White | AN6 | Analog Input 6 | B 12 |
| Brown | AN7 | Analog Input 7 | B 13 |
| Red | AN8 | Analog Input 8 | B 14 |
* The CAN wires must be twisted together.